Any thread product that will sew successfully on lockstitch machines employing Stitch Types 301 and 304 will usually work for embroidery applications.

When a lustrous appearance is preferred for embroidery, the most popular thread types are:

• Continuous filament trilobal polyester
• Mercerised cotton

When a matt appearance is preferred, an apparel thread can be used.

• Polyester wrapped poly core
• Cotton wrapped poly core

If apparel sewing threads are used for embroidery these need to be carefully tested to avoid garment issues. These threads are developed for industrial sewing machines where speeds can exceed 4,000 rpm. The quality and quantity of lubricant used in these sewing threads is different to that of embroidery threads and helps to minimise the friction and abrasiveness while the machine is running at these higher speeds. If apparel sewing threads were to be used for embroidery the lubricant can potentially migrate from the thread and stain the fabric. The lubricant used for embroidery threads is lower and more tightly controlled to allow high performance, outstanding quality, and to minimise the risk of stains.

Trilobal polyester and rayon continuous filament embroidery threads are now in widespread use all around the world.

Polyester threads, in particular, are now becoming more popular because of their ability to with­stand more demanding washing and dry cleaning performance standards. Polyester has advantages over rayon in terms of superior dry and wet strength, abrasion resistance and shade fastness / colour retention.

Coats provide an extensive, creative product range in embroidery and embellishment threads. Metallic sewing threads are a popular modern choice, especially suitable for decorative stitching on all kinds of denim wear and provides a brilliant appearance for special effects. Whether, glow in the dark, reflective or matt effect embroidery, it is your choice.

*Unless specifically dyed with dyestuffs which exhibit minimum colour loss or colour change when exposed to bleach.

Trilobal polyester threads have significantly higher breaking strength as compared to rayon and can be run at sewing speeds exceeding 800 Stitches Per Minute (SPM). With rayon threads, machine speeds cannot usually exceed 600 SPM. As a result trilobal polyester threads greatly enhance machine productivity.

The above table is to be used as a guide. In most cases, a garment manufacturer will be called upon to achieve a combination of objectives (e.g., sheen, strength, abrasion resistance, etc.). In such cases, the appropriate thread which satisfies all the major criteria will have to be chosen.

Just about everything you embroider will require a backing or facing or a combination of both.

• Backings are used to help support the fabric as it is stitched. Backings continue to support the design once it is sewn.
• Facings are used on fabrics with high wales, like corduroy and some knits. Facings help to compact the wales so the stitches do not disappear between them, keeping the wales and picks of fabric from protruding through the design.

Stability of the garment fabric, stitch density, colour, stitch length, stitch speed, size of the embroidery and stability of the design are just some of the variables that can influence backing selection.

Fabric stretch is probably the most important factor in selecting backings. The backing must be stable enough to prevent movement during the stitching process. A fabric’s structure (weave of knit pattern) is apt to be a better indicator of stability than weight alone. Backings are available in different weights. Please check with a backing supplier to ensure you are making the right choice for the fabric being embroidered.

The most common types of embroidery backings are:

• Cutaways – for non-stable fabrics
• Tear-aways – for stable fabrics
• Peel and Stick – for those hard to hoop places
• Hydrostick – for fabrics containing lycra, elastane or spandex

Needle Thread

Tests reveal that on an average you can expect to use about 6.0 metres of thread per 1,000 embroidery stitches. This average will be affected by length of stitches, needle and bobbin tension and fabric thickness.

Bobbin Thread

An estimate of 2.3 metres of bobbin thread per 1,000 stitches is a good starting point. This assumes that, like most embroiderers, you use undyed bobbin threads. Bobbin thread tensions are tighter than needle thread tensions.

Estimating or guessing at potential stitch counts in digitised embroidery designs is just that – ‘guessing’. It can be done and there are a few methods on how to estimate accurately, but there is no foolproof way of knowing prior to digitising how many stitches an embroidery will have.

• You can purchase a plastic see-through grid with 1 ” blocks. Place this grid over the artwork and count the number of 1″ blocks that the grid covers. Then from a chart that accompanies the grid you can see how many stitches per 1″ block. This method provides an estimate as it does not take into consideration the type of stitches being used within the design.
• Or, you can multiply the length by the width of a design. Next multiply that number by 2. This is equal to the amount of 1,000 stitches. For example: 1 ½” (length) x 2″ (width)= 3″; then 3 X 2 = 6. This particular design would have 6 – 1,000 stitches or 6,000 stitches.
• Different stitch types will have different stitch counts. In general a square inch of a solid block of colour will have roughly 1,250 stitches of fill. A linear inch of a satin will have 200 stitches while a linear inch of running will have 50 stitches.
• Lettering a standard block without serifs at¼” tall will have roughly 100 stitches per letter, while ½” lettering will be double. If the font is a serif type, there will be approximately 125 stitches per¼” letter and then 250 stitches for a ½” letter.

This chart defines the number of stitches per letter per different letter heights. For example, one letter at 5mm height has approximately 90 stitches. Two letters at 5mm height has an approximate combined total of 180 stitches.

There are only three types of stitches you need to consider in computerised embroidery:

• Fill Stitch – Multiple lines of walking stitches that fill an entire area; blocks of coloured areas
• Satin or Column Stitch – A series of zig zag stitches that form a letter, line or shape (1 mm – 7mm); such as most lettering or borders wider than 1 mm.
• Running or Walking Stitch – A single, straight stitch that provides detail. Used for outlining small items and widths less than 1 mm or simply to walk from one part of the design to the other.

What does it take to make a good embroidery?
The following is a list of things to. check while ascertaining the quality of your embroidery.

• Flexibility
  Pick up the embroidery- twist and roll it; see what it feels like. Is it flexible?
• Registration
  The embroidery should fit together and be properly aligned, without gaps between the borders.
• Puckering
  Puckering in and around the design does not belong. The fabric should be smooth all around the embroidered area. Puckering can be caused by a tight thread or fabric tension; too wide satin stitches; a dull needle; an unstable fabric (none or wrong choice of backing) and structural jamming.
• Good Stitch Density
  Stitches should be tight and hold together. ff there is a lot of show through between stitches or you can pull them with fingernail; they are too long and will degrade quickly when the garment is laundered.
• 
  Adjusting Stitch Density
  
  Each thread has a unique linear density and has the ability to cover a piece of fabric in a different way. The same thread will cover different fabrics slightly differently, so if you are using the same digitised design on different fabrics, it is important to test the design on the particular fabrics.
  If the stitch density is too high you may experience thread breaks. If the stitch density is too low then ‘gaps’ and ‘grins’ will appear and the fabric colour shows through the embroidered area.
  Points to remember:
  • Using a combination of underlay and cover stitching uses far less stitches than using cover stitching alone therefore always use underlay for large fill areas.
  • Using the correct stitch density will result in a significant saving of unnecessary stitches; an area sewn at a density of 0.55mm uses 20% less stitches than a density of 0.40mm.
  • Each fabric will have a slightly different ability to absorb stitches from a particular thread.

• Balanced Tension
  If there is puckering or pulling of the material around the design, look for proper tension (a balance of top thread and bobbin thread). Turn the garment over to see if there is a balance. You should see 1/3% white stitches in the centre and a balance of coloured stitches on both sides of the white stitches. Too much bobbin will also show on top of the design. If you do not see a balance, tensions are not set correctly.
• Proper Finishing
  Check to see if threads are all clipped and any topping material is removed from the design. Check the backing to see if it properly supports the embroidery, and the excess backing has been removed. Cutaway backings should be clipped at a uniform distance from the edge so as not to look hacked off and should not extend over a half inch or more from the embroidery.

Brand	Image	Description
Sylko		A trilobal polyester thread for machine embroidering.
Sylko EcoVerde		100% recycled trilobal polyester thread for machine embroidery.
Sylko EcoVerde Metallic		A beautiful, metallised embroidery thread with a 100% recycled polyester core yarn.
Sylko EcoVerde Matt AS		100% recycled polyester corespun thread for machine embroidering with an attractive matt appearance. The AS finish is ideal for usage on fabrics that are susceptible to lubrication migration, ensuring significantly decreased or no staining.
Sylko EcoVerde Matt		100% recycled polyester corespun thread for machine embroidering with an attractive matt appearance. The lubrication is carefully adjusted to run perfectly on modern multi-direction embroidery machines at the high speeds they are engineered for.
Sylko AWF		An environmentally friendly, anti-wicking trilobal polyester thread for machine embroidery.
Sylko RD		A trilobal polyester thread with passive flame retardant properties specially engineered for embroidery applications on nightwear.
Sylko Matt		A polyester corespun thread with an attractive matt appearance ideal for machine embroidering
Sylko Pearl		Gives a beautiful pearl effect on embroidery applications.
Sylko Metallic		Highly engineered, embroidery thread which combines a luxurious, lustrous look with quality and high-performance.
Sylko AS		Highly engineered thread, which offers superior lustre and minimises the attraction of down towards the needle. Available with recycled materials.
EcoRegen AS		A range of 100% lyocell threads made from sustainably sourced wood pulp. EcoRegen AS provides a solution for oil sensitive materials such as C0 fabrics and has the potential to reduce lube migration.
Lucence		An embroidery thread with a special ‘Glow in the dark’ effect.
Lucence HD		‘Glow in the dark’ embroidery thread for footwear and accessories.
Signal		A high-tech retro-reflective sewing and embroidery thread for fashion applications in apparel sewing.
Signal HD		A retro reflective sewing and embroidery thread for footwear and accessories embroidery and stitching applications

Please Contatta your local Sales Office to find out more about our embroidery thread options.